RobotGuide

Hardware & electrical · topic E12 · 40 hours

Board design & fabrication

«Designing a board is not drawing wires.» Between the schematic and a small board that actually runs lies a string of details people skip: power tree, power-up sequencing, decoupling, return paths, test points. This skill decides whether you can «only buy modules» or «build a product».

Engineering stage · Hardcore
Embedded & controls · Proficient Mechanical · Aware

Tools
Tools

What to learn

  • The four steps of reading a schematic: power tree → interfaces → clock and reset → protection and test points
  • Power tree: where LDO ends and DCDC begins, power-up sequencing, soft start, current limiting and reverse-polarity protection
  • Decoupling and filtering: why 100 nF and 10 µF sit in parallel, where to put them, how to reckon loop area
  • Stackup and return paths: what separates 2-layer from 4-layer, ground-plane integrity, the price of crossing a split
  • Critical traces: differential pairs, clock lines, high-current paths, Kelvin sensing
  • Packages and soldering: hand-soldering feasibility of 0402 / 0603 / QFN, stencils and reflow, the reality of BGA
  • Fabrication flow: DRC / DFM checks, panelization, impedance control, silkscreen and assembly drawings
  • Power-up flow: current-limited supply → staged verification → test-point priority (power first, then clock, then comms)
  • Being able to: use LCEDA (EasyEDA) or KiCad to design a 4-layer board of «power + MCU + one driver + one comms port» and bring it up

The lesson · plain words

Board-level design is the full path from schematic to fabricated, populated boards. The rule of thumb: the schematic decides «right or wrong», layout decides «usable or not». This page lines up the high-frequency traps of both.

The schematic review checklist

Power: decoupling caps for every chip (E1), power-tree voltage and current re-check, reverse-polarity protection (PMOS or diode). Interfaces: ESD diodes on USB, a CAN termination-resistor jumper, pin headers left on the debug UART. These three spots have the highest rework rate.

Passing ERC/DRC is merely the passing grade. The real review is manual: go pin by pin against the datasheet — pin function multiplexing (you wired an LED to the BOOT pin?), package versus physical dimensions, the direction of polarized parts. One wrong pin = one respin = one month.

Placement and routing: position is performance

Placement priority: place the «electrically tense» combinations first — crystal hugging the MCU, decoupling caps on the power pins, sense resistors far from switching devices, antenna area kept clear. Everything else comes after. Zoning: power / digital / analog / RF, none crossing into another.

Routing iron rules: power traces sized by current, thick before thin (1 A ≈ 0.4 mm at 1 oz); high-speed differential pairs equal-length and equal-spacing (USB/CAN/EtherCAT); a return ground via at every layer change; analog and digital grounds zoned separately and joined at a single point (E7).

Interactive figure · drag it and see

What this figure shows: an exploded PCB stackup — top copper (traces), dielectric, inner copper GND, bottom copper — with a trace hovering over the ground plane, a dielectric-thickness slider, and a live characteristic-impedance readout against a 50 Ω target. Takeaway: impedance is set by trace width, dielectric thickness, and Er — the fab's stackup table is a ready-made answer.

The engineering flow of fabrication and assembly

The fabrication five-step: Gerber output (DRC passing) → order from the board house (impedance control must be written into the order!) → send stencil/BOM/pick-and-place coordinates to the assembler → first-article inspection (placement and polarity) → hand-solder the critical parts. Skip writing impedance control and the fab builds to a default stackup — every impedance ends up off.

Version discipline: every board revision logged in a CHANGELOG (what changed, why, verification result); silkscreen carries version number and date. Three months later you are holding three boards — without records they are three pieces of scrap.

Acceptance: the first-board debugging method

Power-up order for the first board: measure for shorts before inserting any chip → solder the power section alone and measure → solder the MCU and check clock and reset → add peripherals step by step. Solder everything at once in your haste and when smoke rises you will not know what blew.

Acceptance metrics: power-rail ripple, waveforms of critical signals (crystal, PWM, comms), full-load temperature rise (E5). Record all three in the CHANGELOG — only then is this board revision «closed-loop».

Three questions — do you really get it?

1. Which PCB fabrication item is most often overlooked with the heaviest consequences?

  • ASilkscreen font
  • BBoard color
  • CWriting impedance control into the order
Show answer

C. Without impedance control the fab uses its default stackup; every high-speed line's impedance is off, and the problem only explodes at system integration.

2. What should be placed first during layout?

  • AThe biggest chip
  • BThe tense combinations: crystal / decoupling / sense resistors / antenna area
  • CConnectors
Show answer

B. The tense combinations set the zoning skeleton. Place them first and everything else falls into place.

3. The correct first-board bring-up order is?

  • AStaged soldering: power first, then MCU, then peripherals one by one
  • BSolder everything, then power up
  • CSolder the chips but skip the capacitors
Show answer

A. Staged power-up localizes faults one unit at a time. A fully soldered board that blows means starting over from scratch.

Keep going deeper

Links without a marker stay on this site; the rest point to the Chinese edition until its translation batch lands.

How it fails in the field

  • Looking only at function and never at power: wrong power-up order, DCDC self-oscillation, a load transient diving straight into reset
  • Decoupling caps placed too far from the pin: loop area balloons, equivalent to not placing them at all
  • Ground plane shredded by traces: return current takes a detour, and noise and bit errors rise together
  • Powering on right after soldering: no current limiting, no staged verification — one puff of smoke takes out a strip of chips

You have learned enough when

Independently complete a 4-layer board of «power + MCU + one driver + one comms port», from schematic through fabrication to a board that powers up and runs, leaving three artifacts: the power-tree diagram, a staged power-up test record (voltage and current at every stage), and one known defect with a revision plan. In review you can explain «why 100 nF here and not 1 µF».

The Chinese edition carries the full topic page for Board design & fabrication, including the complete outline, depth requirements per career track, and further derivations: robotguide.dev/k/E12/.