RobotGuide

Hardware & electrical · topic E6 · 70 hours

Mechanical design & transmission

The mechanics set the performance ceiling. Same motor, wrong transmission, and the joint is either mushy or rigid as a rock.

Core stage · Hardcore
Embedded & controls · Aware Mechanical · Proficient

Tools
Tools

What to learn

  • The three reducer families: planetary, harmonic, cycloidal — their backlash, stiffness, efficiency, cost
  • How backlash and torsional stiffness affect control bandwidth
  • Bearing selection, tolerance fits, coaxiality
  • The basic ideas of lightweighting and topology optimization

The lesson · plain words

Motors are muscle; the transmission turns muscle power into useful motion. Gear ratio, backlash, inertia matching — these three numbers decide whether your robot is «strong» or «strong but cannot use it».

Gear ratio: the exchange rate between torque and speed

The gear-ratio i trade: output speed ÷i, output torque ×i (times efficiency). But the hidden bill is i² — load inertia reflected to the motor shaft grows with the square. Drag the animation to i=50: inertia explodes 2500× and the servo loop goes dull on the spot.

The inertia matching rule: load inertia ≤ 5–10× rotor inertia. This is the first constraint on reducer selection, more important than whether torque suffices — not enough torque means it cannot do the job; inertia mismatch means it does the job shaking.

Interactive figure · drag it and see

What this figure shows: a gear ratio i slider — output speed ÷i and output torque ×i (at 90% efficiency), with the load inertia seen by the motor computed as ×i² in kg·m², alongside the inertia matching rule load/rotor ≤ 5–10. Takeaway: big i is torque-rich but inertia explodes as i² and response dulls; small i is nimble but the motor suffers — drag toward 51 and i² = 2600 pins the motor down.

Backlash: the invisible tax on precision

Gear meshing always has clearance (backlash); on reversal the output shaft «coasts» for a few arcminutes before taking load again. For a joint with ±0.02mm repeatability, 1 arcminute of backlash over a 100mm arm is 0.03mm — the budget is blown outright.

Countermeasures by price: timing belt (cheap, backlash 0.1–0.5°, compressible with tensioning) → planetary reducer (backlash <10 arcmin) → harmonic reducer (backlash <1 arcmin, the joint favorite) → cycloidal drive (heavy loads). Cost rises down the list; pick by need.

Harmonic vs planetary: the two schools of joint drive

Harmonic: the flexspline transmits force through elastic deformation — zero backlash, single-stage ratios of 50–160; downsides are lower stiffness and its being a source of harmonic vibration — collaborative arms are almost all harmonic. Planetary: good stiffness, high efficiency (>95%), cheap, moderate backlash — used on AGV wheels and high-load joints.

The selection mnemonic: torque density and precision — harmonic; stiffness and lifetime — planetary. Want both? Pay up (premium planetary or cycloidal).

How to verify on the bench

Backlash measurement: fix a dial indicator on the output shaft, rotate forward into position then reverse; the reading difference is the backlash. Stiffness measurement: apply a known torque to the output shaft and measure the angle — high compliance makes force control float (B8's mortal enemy).

Listening is also acceptance: abnormal reducer noises (periodic clicking = tooth surface damage; whining = lubrication or assembly eccentricity). Assembly precision decides reducer lifetime — the installation tolerances in the manual (axial/radial runout) are not suggestions.

Three questions — do you really get it?

1. What is gear ratio i's effect on reflected inertia?

  • A×i²
  • B×i
  • CNone
Show answer

A. Energy accounting: J_reflected = J_load × i². That is why the inertia-matching constraint is sensitive to i.

2. For a collaborative-arm joint needing zero backlash, pick?

  • AHarmonic reducer
  • BPlanetary reducer
  • CTiming belt
Show answer

A. Harmonic flexspline meshing is near-zero backlash. The price is low stiffness — force-control design must compensate for compliance.

3. What is backlash's most direct effect on control?

  • ASpeed cannot go up
  • BPosition error jumps at each reversal and the closed loop chases it back and forth
  • CMore heating
Show answer

B. During the lost motion there is no error feedback; reversal jitter and limit-cycle oscillation are both its work.

Keep going deeper

Links without a marker stay on this site; the rest point to the Chinese edition until its translation batch lands.

How it fails in the field

  • Cranking the gear ratio up for torque: the joint stiffens, becomes non-backdrivable, and collision detection simply stops working
  • Ignoring harmonic reducer resonance (commonly 30–80Hz): force-control bandwidth gets stuck at 10–20Hz

You have learned enough when

You can pick a transmission scheme from a joint's torque, speed, and backlash requirements, and state its impact on control bandwidth.

The Chinese edition carries the full topic page for Mechanical design & transmission, including the complete outline, depth requirements per career track, and further derivations: robotguide.dev/k/E6/.