RobotGuide
Math foundations/The Ledger of One Motor Revolution: Radians, Speed, and Power

Foundations T5 / 27 · From High School

The Ledger of One Motor Revolution: Radians, Speed, and Power

Uniform circular motion, angular velocity, and radians are high-school physics. Every motor nameplate in a robot is a word problem applying these few formulas.

about 20 min2 theorems6 proof steps3 self-test questions

One-line takeaway

Mechanical angle differs from electrical angle by a factor of pole pairs; speed and torque differ by the gear ratio; but power does not lie — P = Tω is an identity in radians.

Animated · spin the wheel and watch radians, degrees, and line speed roll in real time — arc length s = rθ is the distance the wheel covered, not a formula

The gear-ratio ledger of /labs/gear/, the 1kHz control loop of /labs/jitter/, motor sizing in /k/E3/ — the first step of each is this unit-conversion exercise.

Why this tool exists

Choosing a motor: whether the rated speed suffices and whether the torque suffices all comes down to converting ω and T. The nameplate says rpm; the formula wants rad/s.

A 1kHz control loop = one force command every 1 ms — how much mechanical angle per step is a radian problem.

What a 30:1 gear ratio really means, and how much power survives a three-stage gearbox at 97% per stage.

Definitions

Radians and speed units

θ = s/r (arc length over radius, dimensionless). Speed conversion: 1 rpm = 2π/60 rad/s ≈ 0.1047 rad/s. Angular velocity ω = dθ/dt.

Why define it this wayThe radian exists precisely to keep formulas like P = Tω clean: no stray factors like 2π/360. Whoever works in degrees pays an extra factor at every step.

Theorems and proofs

Theorem 1 (P = Tω)

For a rotating shaft with torque T and angular velocity ω, the power is P = T·ω (in radians).

Proof

Turn through a small angle dθ and the point of force application travels an arc length ds = r·dθ. The tangential force F does work dW = F·ds = F·r·dθ.

F·r is exactly the torque T (the lever: force × moment arm), so dW = T·dθ.

Divide both sides by dt: P = dW/dt = T·dθ/dt = T·ω.

NoteWhen sizing a motor you do not need to memorize coefficients to compute power: T=0.1 N·m at 3000 rpm (ω≈314 rad/s) → P≈31.4 W, in one step.

Theorem 2 (the gear-ratio ledger)

For an ideal n:1 gearbox: output speed ÷n, torque ×n, power unchanged. With losses, P_out = P_in × overall efficiency; three stages give 0.97³ ≈ 91.3%.

Proof

Power conservation (ideal): T_out·ω_out = T_in·ω_in.

Substitute ω_out = ω_in/n: T_out = T_in·n. The torque amplification comes precisely from the speed reduction.

Each stage with efficiency η multiplies P by η; n stages multiply by ηⁿ; 0.97³ = 0.91267.

NoteA gearbox amplifies torque, not power. Only a power supply amplifies power — once this ledger balances, a lot of marketing talk collapses on its own.

Work it by hand

A motor rated 3000 rpm and 0.1 N·m drives a 30:1 gearbox (three stages, 97% each). What are the output speed, torque, and power?

  1. Input ω = 3000 × 2π/60 ≈ 314.16 rad/s; input power = 0.1 × 314.16 ≈ 31.4 W.
  2. Overall efficiency = 0.97³ ≈ 0.913; output power ≈ 31.4 × 0.913 ≈ 28.7 W.
  3. Output speed = 314.16/30 ≈ 10.47 rad/s (100 rpm); output torque = 28.7/10.47 ≈ 2.74 N·m.
Answer

100 rpm, 2.74 N·m, 28.7 W — torque amplified about 27× (30× minus efficiency losses), power down 2.7 W, all of it turned into heat inside the gearbox.

Run the numbers

Where the numbers come from

The ledger above is computed item by item for real by the generator:

  • ω_in = 314.2 rad/s, P_in = 31.42 W.
  • 0.97³ = 0.9127, P_out = 28.67 W.
  • ω_out = 10.47 rad/s, T_out = 2.738 N·m.
  • Every conversion is checked against P = Tω — if the books balance, good; if not, check the units first.

Where this shows up

The object hereThe counterpart in RLUsed in
ω = 2π·rpm/60The unit of velocity commands in the servo loopused in →
1kHz → 1ms/stepThe mechanical angle increment per control periodused in →
P = TωThe power ledger of motor sizingused in →

Boundaries: where this article stops

This article stops at constant speed. During acceleration the torque comes from T=J·α (rotational inertia); current loops, back-EMF and the rest of the electrical side live in /k/E2/ and /k/E3/. For sizing practice see /labs/gear/.

Self-test: 3 questions

All hand-computation and «find the flaw in this proof» questions — nothing to memorize. Stuck? Go back to the section.

01How many rad/s is 3000 rpm?

3000 × 2π/60 = 100π ≈ 314.16 rad/s. Memorizing the rough factor rpm × 0.1047 also works.

02The gear ratio amplifies torque; why doesn't it amplify power?

The speed shrinks by the same factor, and the two cancel in P = Tω. Power is decided only by the supply and the efficiency.

03A three-stage gearbox at 97% per stage: what is the overall efficiency?

0.97³ = 91.3%. Efficiencies multiply, they do not add — that is why a 1% difference is worth money.

Up next

The full series · 27 articles

T1The Matrix Is a Ledger for Rotation≈ 25 minT2From Slope to Gradient: The First Line of Every Robot Learning Algorithm≈ 25 minT3Vectors and forces: the physical reading of the dot productAbout 20 minT4Two Rulers and a Better Rulerabout 25 minT5The Ledger of One Motor Revolution: Radians, Speed, and Powerabout 20 minT6Complex multiplication is rotation: the one-dimensional version of quaternionsAbout 20 minT7Bases and coordinates: why robots put everything in matrices45 minT8Matrix Multiplication: Chaining Transformations, Not a Table OperationAbout 40 minT9The Jacobian: Rotate a Joint One Degree — How Far Does the End Effector Move?About 45 minT10Eigenvectors: The Directions a Matrix Dare Not Touchabout 45 minT11SVD and the Pseudoinverse: When There Is No Exact Solution, Find the Nearest Oneabout 50 minT12Taylor expansion: putting a straight line to work in place of a curveAbout 40 minT13Probability spaces: why «random» needs axioms50 minT14Expectation: A Rigorous Construction of «Average»About 55 minT15Conditional Expectation: What the Vertical Bar Really Means≈ 60 minT16Four inequalities: the quantitative answer to «how many samples are enough»45 minT17Norms and fixed points: where «it always converges» comes from55 minT18Markov Chains: When the Time Average Equals the Ensemble Averageabout 55 minT19The Mathematical Construction of the MDP: What One Axiom Is Worthabout 50 minT20Dynamic Programming: The Accounting for Two Iterations≈ 50 minT21Optimization: why constraints cannot rely on penalties aloneAbout 55 minT22Stochastic Approximation: Every Term in the Learning-Rate Formulaabout 55 minT23The Mathematics of Contact: Hertz Theoryabout 45 minT24Friction and the Friction Cone: The Geometry of Constraintsabout 40 minT25Force Closure and Grasp Metrics: ε Is a Linear ProgramAbout 50 minT26Contact Kinematics: Why Rolling Is Not «Sliding Along»≈ 45 minT27Slip detection: from «I felt it» to «I computed it»About 50 min